Ntl250 modem hack

Por cierto, con luces y todo, que detalle. Salu2 Keep on Rollin'. Hola Valentino, pues mira un amigo mio , lo hizo funcionar y el camino que detallas es el indicado, usando sb que es el que tengo legalito.. Podria usar esos datos, pero no deseo.. Usando schwez 1. Hola Amigos, tengo un problema que no tenia antes, escaneo Mac pero no encuentro ningun config, antes encontraba muchos..

Estroy escanenado con Coax Thief y tambien Dhcpforce.. Hola Amigo, algo paso por aca , por que mi Isp esta filtrando los archivos de configuracion del modem, realize un escaneo de mas 3 horas y nada.. Conoces algun soft mas potente para monitorizar esto, si es en linux no hay problema. Maestro al parecer mi Isp esta filtrando la informacion de archivos de configuracion del modem..

Como se resuelve esto? Manbraver Manbraver Ver perfil Ver mensajes del foro. Hola manes interezante su tema Antes un virus se propagaba con una facilidad terrible una vez insertado en la red de un nodo de internet por cable.

El mejor software, por lo potente y simple, para mi gusto es tcpdump. The NTL is a cable modem, and is not a router. Await shipment. Maybe the Wireless AP you purchased can handle routing as well. Really, a router is a router. Out of desperation head to Maplin. Uh oh. The only wireless cable modem router in stock is a Netgear. Yeh, that was never going to work. Phone up again and lie, tell them you are setting up a Linksys.

There are many reasons you would want to do this: You have a complex network setup with a more advanced router running services such as a VPN server and you still want to use the VOIP in the TG so that it can manage the packet priority tagging properly. You don't quite trust the TG You want a simpler solution than the "Using bridge mode with a dedicated PPPoE ethernet port" section below outlines which can be a nightmare to set up and debug if something goes wrong.

This is still possible in bridged mode but it's less stright forward. Here is how you go setting this up properly: Set up the TG as above fully including VOIP etc and make sure it works to your satisfaction. If your inner router also has a default LAN subnet of Confirm on the inner router that it got If it did not, reboot both of them at the same time to get rid of any lingering DHCP leases.

Set up DynDNS if you want to. Turn off WiFi on the TG At this point the TG should be transparent to incoming requests which will hit the WAN interface of your internal router and be handled normally. Really advanced topics! Changing max sync speeds You can change the max values for sync speeds.

The value maxusdatarate controls the upstream maximum sync speed, maxdsdatarate controls the downstream maximum sync speed, and maxaggrdatarate is the maximum combined speed. The defaults are listed below. If you won the node lotto and are feeling lucky you can modify these like so: uci set xdsl. It should also work with IPoE. Thankfully, standard OpenWRT config applies.

I have yet to figure out how to get the WAN port to do this — as it seems to be configured differently — maybe at the switch level. If you want to use the VOIP in the TG while in bridge mode, you will need to configure a default gateway, a nameserver, and configure the pabx to use the LAN bridge as the outgoing interface. The following example uses Google for DNS and assumes your router is at The web interface will see the section in the config once you add it in.

It would be possible to add the section using UCI but it's quicker with an editor and you will get the most recent defaults from your existing profile rather than a stale web page!

This should also be possible via the web interface after running the above default config which adds in a web page to allow editing this config. This was straight forward for me. Serial Console A serial console can be added using a 3. These can be found on ebay quite cheaply.

The serial console is J5 on the board, and note from the picture below, R and R need to be solder bridged to pass the serial signals to the adaptor. Note that by default you can't log in on the serial console.

I was very happy to find this hidden gem. Sadly there is no icon for it so I had to reuse one.